Dakota Digital MAN 650210 INSTALLATION INSTRUCTIONS LAT NR330 LED Tail Lights for 1940 53 Chevrolet Pickup Kit includes 1 Remove the screw that holds the lens on and remove from the housing 2 Remove the light bulb s from the socket s 3 Disconnect the tail light wires from the vehicle If there is no place to disconnect the wires the wires will need to be cut and will be spliced to the LED assembly later 4 Remove and save the screws that hold the bulb sock
Dakota Digital MAN 650218 INSTALLATION INSTRUCTIONS LAT NR271 LED Tail Lights for 1970 Impala Caprice Kit Includes Installation 1 Remove the two screws and lens on each tail light 2 Remove the light bulb from socket 3 Carefully remove the gasket from the housing If the gasket is hard or brittle it should be replaced 4 Now is a good time to clean or replace the lenses and housings if necessary If the lenses are in poor condition a replacement set is r
INSTALLATION INSTRUCTIONS LAT NR340 LEDTail Lights for 73 87 Chevy Fleetside Pickup and 87 91 Suburban Blazer MAN 50203 Kit Includes Installation Dakota Digital 1 Remove the tail light lenses There are four screws holding each lens in place 2 Remove the light bulbs 3 Now is a good time to clean the lenses and housings If lenses are in bad shape a new set is recommended 4 DO NOT remove the tape from the LED assemblies yet MAN 650203
North Dakota Weatherization Field Standards Home Weatherization Assistance Program January 2003 Edition State of North Dakota Department of Commerce Division of Community Services DCS Paul Govig Director Energy Division Howard Sage Weatherization Program Administrator 400 East Broadway Bismarck ND 58502 701 328 4140 Acknowledgements The revision of this document was part of the project called Best Practices for North Dakota Weatherization This project was
Dakota Alert Inc DCHT 2500 Wireless Rubber Hose Transmitter Owner s Manual Warnings This device complies with Part 15 of the FCC rules Operation of this device is subject to the following conditions 1 This device may not cause harmful interference 2 This device must accept any interference including interference that may cause undesired operation Installation The DCHT 2500 transmitter consists of a transmitter box and 25 feet of hose To install connect the
WWW DHKOTHDIEITHL COM VM 150 Victory installation kit for MCL 5000 Series gauges VM 170 Victory installation kit for MCV 7000 Series gauges I Kit includes 1 Wiring harness 1 Turn signal cross over harness 1 Mounting bracket 2 Socket head screws with nuts Removing the original gauge Remove the headlight retaining ring and the headlight to expose the wiring harness Unplug white 4 pin connector and remove the original speedometer wiring harness Remo
Manufactured by Dakota Digital ODY 16 1 rev A DIGITAL CLOCK ODY 16 1 ORANGE RED BLACK BLUE Function Connect to a constant 12 volt power point This will keep the correct time Connect to switched 12 volt powerpoint An accessory terminal will work for this Connect to a good ground point in the vehicle Connect to the tail light circuit A 1 Vie Y CUTOUT measurements not actual size lt 2 Vie gt MANUAL 650147A 1
Dakota Digital MAN 650210 INSTALLATION INSTRUCTIONS LAT NR330 LED Tail Lights for 1940 53 Chevrolet Pickup Kit includes 1 Remove the screw that holds the lens on and remove from the housing 2 Remove the light bulb s from the socket s 3 Disconnect the tail light wires from the vehicle If there is no place to disconnect the wires the wires will need to be cut and will be spliced to the LED assembly later 4 Remove and save the screws that hold the bulb sock
Dakota Digital MAN 650154 INSTALLATION INSTRUCTIONS LAT NR120 LEDTail Lights for 62 64 Nova Kit Includes Installation 1 Remove the tail light lens 2 Remove the light bulb 3 Remove the original bulb connector from the back side of the housing 4 Now is a good time to clean or replace the lens and housing if necessary 5 Remove the two screws and aluminum plate from the back of the new LED assembly 6 Insert the new LED assembly thr
WWW DHKOTFIDIEITRL COM MCL 36K TCH Thank you for purchasing the Dakota Digital MCL 36K TCH gauge for your Harley Davidson Touring bike This gauge is designed to be a direct plug in replacement for all touring models from 2004 2011 This is part of a six gauge package for touring models so you can add additional gauges as you choose INSTALLATION First read and familiarize yourself with all of the components and this manual The first step is to remove the seat and disconn
Dakota Digital INSTALLATION INSTRUCTIONS LAT NR241 LED Tail Lights for 1959 Chevrolet Impala Bel Air Biscayne MAN 650212 Kit Includes Installation 1 Remove the original bulb sockets U 2 Remove the tail light housing hardware so the housing can be removed from the car 3 Remove the chrome trim from the tail light housing The outer trim is snapped into place and will need to be gently pried off with a flat blade screwdriver or similar tool 4 N
Dakota Digital MODEL HLY 5000X Rev A BAR MOUNT SPEEDOMETER TACHOMETER INFORMATION SYSTEM Please read this before beginning installation or wiring POWER Connect the red wire from the main harness to accessory power from the ignition switch A good quality solid state ignition switch should be used The contacts on a mechanical bar switch can bounce due to the vibration and cause the system to momentarily loose power and reset itself Never connect this to a b
SECTION TABLE OF CONTENTS PAGE INTRODUCTION 3 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 7 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 INSTRUMENT PANEL AND CONTROLS 147 STARTING AND OPERATING 193 WHAT TO DO IN EMERGENCIES 271 MAINTAINING YOUR VEHICLE 289 MAINTENANCE SCHEDULES 347 IF YOU NEED CONSUMER ASSISTANCE 367 INDEX 375 INTRODUCTION CONTENTS Introduction 4 How To Use This Manual 4 Warnings And Cautions 5 I Veh
DAKOTA ALERT Wireless Alarms amp Security Equipment AD 01 Kit Auto Dialer Owner s Manual s V AD 01 Kit Manual indd 1 10 15 2009 10 17 55 AM Warnings This device complies with Part 15 of the FCC rules Operation of this device is subject to the fol lowing conditions 1 This device may not cause harmful interference 2 This device must accept any interference including interference that may cause undesired operation
INSTRUaiONS O A DAKOTA DIGITAL INSTRUM ENT amp LIGHTING APPAREL amp ACCESSORIES DAKOTA DIGITAL Each unit is completely individual no control box Exclusive warning feature allows reading to flash when outside normal operating limits Start up circuitry provides fast accurate readings and no waiting for readings to stabilize All units feature high contrast non glare teal displays for excellent daytime visibility and have nighttime dimming capa
Dakota Digital SERIES II VACUUM FLUORESCENT DIGITAL DASHBOARD The latest in digital dashboard technology for the street rodder car and truck enthusiast INSTALLATION AND OPERATION MANUAL Please read this before beginning installation or wiring MODELS STR3D STR4D STR5D amp STR6D Dakota Digital 3421 W Hovland Ave Sioux Falls SD 57107 Phone 605 332 6513 FAX 605 339 4106 Thank you for purchasing the Vacuum Fluorescent Digital Dashboard from DAKO
Dakota Alert Inc BBT 2500 Break Beam Transmitter User Guide www dakotaalert com PRODUCT DESCRIPTION The BBT 2500 is used with the DCR 2500 receiver The BBT 2500 uses Active Infrared to detect anything that passes through the sensor pair and breaks both beams at the same time When the beams are broken the unit sends a signal to the receiver This will sound one of four different tones Classical Westminster Chime Ding Dong or Whistle The BBT 2500 can be used to m
Dakota Digital MAN 650204 INSTALLATION INSTRUCTIONS LAT NR350 LED Tail Lights for 1964 1966 Mustang Kit Includes Installation 1 Remove both right and left tail light lenses as described below at the same time taking care to keep the left and right lenses and trim with the correct side of the vehicle 2 Remove the four screws that hold the chrome tail light trim piece 3 Remove the tail light trim piece and the lens 4 Remove the light bulb from socket 5
Dakota Digital MAN 650246 INSTALLATION INSTRUCTIONS LAT NR181 LEDTail Lights for 1972 Impala Kit Includes Installation 1 Remove the tail light housing from the vehicle 2 Remove the tail light lens 3 Remove the light bulb 4 Remove the original bulb connector from the back side of the housing 5 Now is a good time to clean the lens and housing If lenses are in bad shape a new set is recommended 6 Remove the nuts and back plate from the back of the
SECTION TABLE OF CONTENTS PAGE 1 I INTRODUCTION 3 2 I THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 7 3 I UNDERSTANDING THE FEATURES OF YOUR VEHICLE 55 4 I INSTRUMENT PANEL AND CONTROLS 93 5 I STARTING AND OPERATING 141 6 I WHAT TO DO IN EMERGENCIES 207 7 I MAINTAINING YOUR VEHICLE 219 8 I MAINTENANCE SCHEDULES 261 9 I IF YOU NEED CONSUMER ASSISTANCE 279 10 INDEX 287 INTRODUCTION CONTENTS Introduction 4