16104 Backsaver Auger Specifications SPECIFICATIONS Y16104 I Tubing Tubes 1 and 2 10 gauge Tubes 3 4 5 11 gauge Flighting H on swing and main auger Flighting shaft 3 diameter 46 wall Undercarriage 5 X 5 X square tube Lift arms H formed tubing Bridging Upper bridging cable Side bridging cable Wheel and hubs i 8 bolt hubs 16 5 Lx 16 1x10 ply Hopper dimensions 48 X 60 X 13 tall Clearance in down position i 14 10
GASOLINE EARTH AUGER USER S MANUAL 50cc EARTH AUGER Please read and understand these instructions prior to operating the earth auger FUEL MIX One part two stroke oil to twenty five parts 91 octane unleaded petrol NOTE For the first three hours of usage use a twenty to one fuel mixture This will aid the running in of the engine Never use less then a twenty five to one fuel mixture This will damage the engine COLD ENGINE STARTING e Ignition switch on back
Gauger420 User Manual You Can Measure the Solid Benefits Notices and safety guidelines This manual is delivered subject to the following conditions and restrictions e The manual contains proprietary information belonging to Solid Applied Technologies Ltd The information is published solely for the purpose of assisting authorized users of Gauger420 e No part of this manual may be used for any other purpose or disclosed to any person or firm or repro
Gauger420 User Manual M7 E N 2e a N ba J Y sm e fe gt f j AA You Can Measure the Solid Benefits Notices and safety guidelines This manual is a detailed technical guide for Gauger420 level sensor Some information in this manual refers to GaugerGSM GaugerGPS and Gauger485 sensors and cannot be applied to other Gauger models The manual is published under the following conditions and restrictions Some features are firmware hardw
GaugerGSM User Manual You Can Measure the Solid Benefits Notices and safety guidelines This manual is delivered subject to the following conditions and restrictions e manual contains proprietary information belonging to Solid Applied Technologies Ltd The information is published solely for the purpose of assisting authorized users of the GaugerGSM e No part of this manual may be used for any other purpose or disclosed to any person or firm or
Slide Gate Auger Gravimetric Batch Blenders With Mitsubishi Controller Part Number A0567659 Bulletin Number SM1 605M 1 Effective 6 10 05 C Write Down Your Serial Numbers Here For Future Reference We are committed to a continuing program of product improvement Specifications appearance and dimensions described in this manual are subject to change without notice DCN No _ Copyright 2004 All rights reserved Shipping Information Unpacking and Inspection
3898 93110 711 OWNER OPERATOR MANUAL The engine exhaust from this product contains chemicals known to the State of California to cause cancer birth defects or other reproductive harm NOTE Drill is optional part Thank you for purchasing a RedMax product Before using our power auger please read this manual carefully to understand the proper use of your unit Read this manual carefully to understand all safety precautions controls proper operatio
T4507 93110 603 RedMax OWNER OPERATOR MANUAL POWER AUGER AG4300 Thank you for purchasing a RedMax product Before using our power auger please read this manual carefully to understand the proper use of your unit APPLICABLE SERIAL NUMBERS 100101 and up WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer birth defects or other reproductive harm A Read this manual carefull
KRAMBLE INDUSTRIES INC Remote Control Swing Auger Mover Installation and Operating Manual The Remote Control Swing Auger Mover is designed to provide the ultimate in convenience and safety to perform tasks remotely It is a radio frequency RF controlled device that allows operation of a motor gate chute etc from a hand held transmitter operated remotely The Transmitter which operates at 916 MHz FM transmits encoded information to the Receiver which then decodes the
T4511 93120 506 ZEnoniH PARTS LIST POWER AUGER AG4300 AG531 NOTE 1 Use ZENOAH genuine parts specified in the parts list for repair and or replacement 2 ZENOAH does not warrant the machines those which have been damaged by the use of any parts other than those specified by the company 3 When placing orders of parts for repair and or replacement check if the model name and the serial number are suitable to those specified in the parts list then use parts
T4511 93120 506 ZEnoniH PARTS LIST POWER AUGER AG4300 AG531 NOTE 1 Use ZENOAH genuine parts specified in the parts list for repair and or replacement 2 ZENOAH does not warrant the machines those which have been damaged by the use of any parts other than those specified by the company 3 When placing orders of parts for repair and or replacement check if the model name and the serial number are suitable to those specified in the parts list then use parts