Dewalt D25601K TYPE 1 User Manual DRILL HAMMER Manuals And Guides 1503313L
User Manual: Dewalt D25601K TYPE 1 D25601K TYPE 1 DEWALT DRILL HAMMER - Manuals and Guides View the owners manual for your DEWALT DRILL HAMMER #D25601KTYPE1. Home:Tool Parts:Dewalt Parts:Dewalt DRILL HAMMER Manual
Open the PDF directly: View PDF .
Page Count: 7
|Open PDF In Browser||View PDF|
LULU t) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits, etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. @ AC] K8 Zt"0 Z >-o o_> __b 5) SERVICE a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. cccc coco w_z C3 W Additional OCO • • • cow zoo w< O,W Z ,, "0 < • O_FwO • 0 "F-,,-A, _Z m ,co< cr • r-co co< < Z(SD • • • • • • • 7 • Safety Instructions More Than 0 6 10 12 DEWALT Industrial Tool Co., 701 Joppa Road, Towson, MD 21286 Part No. N392151 D25501, D25553, D25601, D25603, D25651, D25831, D25851 Copyright © 2010, 2014 DEWALT The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the "D" shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the array of lozenge-shaped humps on the surface of the tool. Definitions: Safety Guidelines The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols. _DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. _, WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. ,_ CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. NOTICE: indicates a practice not related to personal injury which, if not avoided, may result in property damage. IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258). WARNING: To reduce the risk of injury, read the instruction manual. General _ Power Tool Safety Warnings ARNING! Read allresult safetyin warnings and all and instructions may electric shock, fire instructions. and/or seriousFailure injury, to follow the warnings SAVE ALL WARNINGS FOR FUTURE AND INSTRUCTIONS REFERENCE The term "power tool" in the warnings refers to your mains-operated battery-operated (cordless) power tool (corded) power tool or 1) WORK AREA SAFETY a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control 2) ELECTRICAL SAFETY a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified p/ugs and matching outlets will reduce risk of electric shock. b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. 0 If operating a power tool in a damp location is unavoidable, use a ground fault circuff interrupter (GFCI) protected supply. Use of a GFC/ reduces the risk of electric shock. 3) PERSONAL SAFETY a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury, b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. c) Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source and/or battery pack, picking up or carrying the tool Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents. d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury, e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. 0 Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. 4} POWER TOOL USE AND CARE a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c) Disconnect the plug from the power source andlor the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally, d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool Power tools are dangerous in the hands of untrained users. e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. Hammers Wear safety goggles or other eye protection. Hammering operations cause chips to fly, Flying particles can cause permanent eye damage. Wear a dust mask or respirator for applications that generate dust. Ear protection may be required for most applications. Keep a firm grip on the tool at all times. Do not attempt to operate this tool without holding it with both hands. Operating this tool with one hand will result in loss of control. Breaking through or encountering hard materials such as re-bar may be hazardous as well. Tighten the side handle securely before use. Do not operate this tool for long periods of time. Vibration caused by hammer action may be harmful to your hands and arms. Use gloves to provide extra cushion and limit exposure by taking frequent rest periods. Do not recondition bits yourself. Chisel reconditioning should be done by an authorized specialist. Improperly reconditioned chisels could cause injury, Wear gloves when operating tool or changing bits. Accessible metal parts on the tool and bits may get extremely hot during operation. Small bits of broken material may damage bare hands. Never lay the tool down until the bit has come to a complete stop. Moving bits could cause injury, Do not strike jammed bits with a hammer to dislodge them. Fragments of metal or material chips could dislodge and cause injury, Keep the power cord away from the rotating bit. Do not wrap the cord around any part of your body. An electric cord wrapped around a spinning bit may cause personal injury and loss of control Air vents often cover moving parts and should be avoided. Loose clothes, jewelry or long hair can be caught in moving parts. An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that is 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. When using more than one extension to make up the total length, be sure each individual extension contains at least the minimum wire size. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. Minimum Gauge for Cord Sets Volts Total Length of Cord in Feet (meters) 120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7) 240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4) Ampere Rating (MAR14) for Rotary Wear ear protectors. Exposure to noise can cause hearing loss. Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury, Holdpower tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock. Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control Not More Than 6 10 12 16 AWG 18 18 16 14 16 16 16 12 16 14 14 12 14 12 Not Recommended _ WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses. Also use face or dust mask if cutting operation is dusty, ALWAYS WEAR CERTIFIED SAFETY EQUIPMENX • ANSI Z87.1 eye protection (CAN/CSA Z94.3), • ANSI $12.6 ($3.19) hearing protection, • NIOSH/OSHA/MSHA respiratory protection. _WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. • Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals. WARNING: Use of this tool can generate and/or disperse dust, which may cause serious and permanent respiratory or other injury, Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body, _WARNING: Always wear proper personal hearing protection that conforms to ANSI $12.6 ($3.19) during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss. • The label on your tool may include the following symbols. The symbols and their definitions are as follows V..................... volts A ......................... amperes Hz ................... hertz W........................ watts min ................. minutes q_ or AC ............. alternating current - -- or DC ..... direct current _-, or AC/DC ...... alternating or direct current (_) ................... Class I Construction no ....................... no load speed ....................... (grounded)  ................... Class II Construction ....................... (double insulated) .../min ............ per minute IPM ................. impacts per minute SPM ............... strokes per minute SAVE THESE n ......................... @ ....................... ,_1, ........................ BPM ................... RPM ................... sfpm ................... INSTRUCTIONS rated speed earthing terminal safety alert symbol beats per minute revolutions per minute surface feet per minute FOR FUTURE USE Motor Be sure your power supply agrees with the nameplate marking. Voltage decrease of more than 10% will cause loss of power and overheating. DEWALT tools are factory tested; if this tool does not operate, check power supply. COMPONENTS (Fig. 1) _, WARNING: Never modify the power tool or any A. Trigger switch (D25501, D25553, D25601, D25603, D25651) Toggle switch (D25831, D25851) B. Lock-on slider (D25501, D25553, D25601, D25603, D25651) C. Side handle D. Main handle part of it. Damage or personal injury could result. E. SHOCKS Active Vibration Control ® System (D25651, D25601, D25603, D25831, D25851) F. Mode selector G. Electronic Speed and impact control dial H. Clamp wheel I. Rear side handle position INTENDED USE These heavy-duty rotary hammers have been designed for professional hammerdrilling, and chipping at various work sites (i.e., construction sites). DO NOT use under wet conditions or in presence of flammable liquids or gases. These heavy-duty rotary hammers are professional power tools. DO NOT let children come into contact with the tool. Supervision is required when inexperienced operators use this tool. ASSEMBLY AND ADJUSTMENTS _ WARNING: To reduce the risk of injury, turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs. An accidental start-up can cause injury, Side Handle (Fig. 1) D25501, D25553, D25601, D25603, D25851 _WARNING: To reduce the risk of personal injury, ALWAYS operate the tool with the side handle properly installed and securely tightened. Failure to do so may result in the side handle slipping during tool operation and subsequent loss of control Hold tool with both hands to maximize control The side handle clamps to the front barrel (collar) and may be rotated 360 ° to permit right or lefthand use. For operating convenience, the side handle can be installed in front or rear positions. TO MOUNT IN FRONT POSITION (FIG. 2) 1. Unscrew the side handle (C) and disassemble the side handle clamp (J). 2. Snap the steel ring (K) over the collar (L) behind the tool holder (M). Squeeze both ends of the steel ring together. Mount the bushing (N) and insert the pin (O). 3. Slide the side handle clamp (J) onto the bushing (N) while keeping the pin (O) centered. Lightly screw the clamp wheel (H) onto the busing (N)--do not tighten. 4. Screw the side handle (C) into the clamp knob (H) and tighten. 5. Rotate the side handle mounting assembly to the desired position. For hammerdrilling horizontally with a heavy drill bit, place the side handle assembly at an angle of approximately 20 ° to the tool for optimum control. 6. Lock the side handle mounting assembly in place by securely tightening the clamp wheel (H) so that the assembly will not rotate. TO MOUNT IN REAR POSITION (FIG. 3} 1. Unscrew the side handle (C) and remove it from the side handle mounting assembly. Leave the side handle mounting assembly in the front position. 2. Screw the side handle directly into one of the rear side handle positions (I)on either side of the tool. D25831, D25851 (FIG. 4} 1. Unscrew the D-shaped handle knob (R). FIG. 1 2. Slide the D-shaped handle (Q) and assembly over the tool holder (M) and onto the collar (L) in the mounting area (Z). The correct position of the D-shaped handle (Q) is between head and middle of the tube. CHISEL BIT ADJUSTMENT MODE MODE DE RE!_GLAGEDU TR[!_PAN ORDINAIRE MODO DE AJUSTE DE l=A,BROCA DE CINCEL HAMMERDRILLING MODE MODE DE MARTEAU PERFORATEUR MODO TAI.._ADROPERCUTOR 3. Adjust the D-shaped handle to the desired angle. 4. Slide and rotate the D-shaped handle to the desired position. 5. Lock the D-shaped handle in place by securely tightening the knob (R) so that the D-shaped handle assembly will not rotate. CHIPPING MODE MODE DE BURINAGE MODO CINCEL SHOCKS Active CHISEL BIT ADJUSTMENT MODE MODE DE R_!!G[AGE DU TRE!_PANORDINAIRE MODO DE AJUSTE DE LA BROCA DE CINCEL Inserting E F I G and Removing Inserting ® System (Fig. 1, 8) Spline Drive Accessories (Fig. 5) and Removing SDS Max Accessories (Fig. 6) D25501, D25601, D25603, D25831 1 Pull back the locking sleeve
Source Exif Data:File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 7 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Sat Mar 28 09:59:59 2015 Author : Title : Subject :EXIF Metadata provided by EXIF.tools