GreenSpring Modular I O IP Unidig E 48 48 Line Input Output with LineSafe ESD Protection IndustryPack User s Manual Manual Revision 3 7 28 99 Hardware Revision B IP Unidig E 48 415 327 3808 FAX 48 Line Input Output with LineSafe M ESD Protection IndustryPack GreenSpring Computers 181 Constitution Drive Menlo Park CA 94025 415 327 1200 This document contains information of 1994 1996 by GreenSpring Computers Inc n E IndustryPack is a t
UBEX Dig iDig Troubleshooting Communication with LED Display is lost The LED display is mandatory for the functionality of iDig as it is the system s antenna Unplug amp re plug the LED antenna Watch that you don t plug it twisted 180 rotated Ifthe individual LEDs of the display are ON the cable set seems to be broken Ifthe individual LEDs of the display are OFF either the cable set or the LED display are broken Sensor s missing or getting contin
Fluidigm PN 100 6812 REV A2 USER GUIDE D3 Assay Design Copyright 2013 Fluidigm Corporation All rights reserved Fluidigm the Fluidigm logo Access Array BioMark C D3 Assay Design DELTAgene Dynamic Array and SNPtype are trademarks or registered trademarks of Fluidigm Corporation in the U S and or other countries For Research Use Only Not for use in diagnostic procedures PN 100 6812 Rev A2 Contacting Fluidigm On the internet www fluidigm com sup
marn id s p Application Note Configuration of 1 x miniDSP 2 x miniDIGI Disclaimer Please make sure to read the miniDIGI and miniDSP user manual This application is not intended as a one for all application note since each board is highly configurable Note that in this configuration only ONE miniDIGI can be used as a source for the digital section This configuration has the following clocking configuration 1 x miniDIGI as I2S master 1 x miniDIGI as I2S slave
inmid sp miniDIGI I O card USER MANUAL V1 3 Revision Description Date V1 0 User manual Initial version 25 02 2010 V1 1 Updated section on Digital Analog toggle switch 05 05 2010 V1 2 Updated diagrams for I2S section 02 06 2010 V1 3 Updated general descriptions 01 02 2011 inmid sp 1 Board connectivity 1 1 Board diagram Toslink 1 Toslink 2 SPDIF 1 SPDIF 2 Expansion connector J2 Master Slave jumper DC in SPDIF OUT
Utilisateur Applications UBEX L Version Manuel 2 00 Version Logiciel 2 03 Langue Fran ais Pour plus de d tails visitez notre site Wwww idig system com Informations de s curit Aimants Manipulez avec une grande pr caution les aimants mont s dans les plaques iDig Les plaques support destin es fixer solidement les capteurs sur la pelle utilisent des aimants tr s puissants Ils doivent tre manipul s avec pr caution pour vite
Dynamic C Integrated C Development System For Rabbit Microprocessors iDigi Services for Rabbit Developer s Guide 90001161_A iDigi Services for Rabbit Developer s Guide Part Number 90001161 A e Printed in U S A Digi International Inc 2007 2010 Allri ghts reserved Digi International Inc reserves the right to make changes and improvements to its products without providing notice Trademarks Rabbit and Dynamic C are registered trademarks of Digi Inte
e 2 Everbrite umiDigit f E LED Electronic Price Display System Owner Operator Manual ATTENTION The radio console is designed for long range communication Use at close distances may cause inconsistent operation As a rule always test and or operate at L distances of 15 feet 5 meters or greater p VOLUME VII IN00946P Rev 06 01 2010 lumiDigit Copyright Everbrite LLC 2007 2010 This is the exclusive property of Everbrite LL
O Gli estensori dita BORT servono a normalizzare la funzione del tendine La di namica flesso estensione del dito consente di sgravare dal carico o di riabilitare gradualmente le parti lese del tendine Indicazioni d uso Si pu utilizzare la stecca per il dito sia per l articolazione interfalangea prossimale PIP vedi illustrazione 1 nonch per l articolazione in terfalangea distale DIP vedi illustrazione 2 Potete aumentare o diminuire la pressione piegando la molla con
UBEX Dig iDig Troubleshooting Controlbox doesn t switch on The fuse inside the cigarette lighter plug may be broken Open the cigarette lighter plug and replace it with a 5A fuse The cigarette lighter socket of the machine is broken Communication with LED Display is lost The LED display is mandatory for the functionality of iDig as it is the system s antenna Unplug amp re plug the LED antenna Watch that you don t plug it twisted 180 rotated