Weber 42377 Users Manual Summit BI NG SB OwnersGuideWinstall 011806

Summit Built-In NG Side Burner to the manual c3be5d52-ab22-46f4-a5d5-784c8e0a2d00

2015-01-05

: Weber Weber-42377-Users-Manual-161909 weber-42377-users-manual-161909 weber pdf

Open the PDF directly: View PDF PDF.
Page Count: 12

SUMMIT®#
42377
42377 US 01/18/06
NG
YOU MUST READ THIS OWNERS GUIDE
BEFORE OPERATING YOUR GAS GRILL
BUILT-IN NG SIDE BURNER INSTALLATION/OWNER'S GUIDE
Summit® Built-In NG Side Burner
THESE ACCESSORIES MAY BE PURCHASED
SEPARATELY.
DANGER
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open fl ames.
3. Open lid.
4. If odor continues, keep away from the
appliance and immediately call your gas
supplier or your fi re department.
Leaking gas may cause a fi re or explosion
which can cause serious bodily injury or
death, or damage to property.
WARNING
1. Do not store or use gasoline or other
ammable liquids or vapors in the vicinity
of this or any other appliance .
2. An LP cylinder not connected for use shall
not be stored in the vicinity of this or any
other appliance.
WARNING: Follow all leak-check procedures
carefully in this manual prior to barbecue
operation. Do this even if the barbecue was
dealer-assembled.
NOTICE TO INSTALLER: These instructions
must be left with the owner and the owner
should keep them for future use.
THIS GAS APPLIANCE IS DESIGNED FOR
OUTDOOR USE ONLY.
WARNING: Do not try to light this appliance
without reading the “Lighting Instructions”
section of this manual.
2DANGERS & WARNINGS
DANGER
Failure to follow the Dangers, Warnings and Cautions contained in this Owners Manual may result in serious bodily
injury or death, or in a fi re or an explosion causing damage to property.
WARNINGS
Do not store a spare or disconnected liquid propane cylinder under or near this barbecue.
Improper assembly may be dangerous. Please carefully follow the assembly instructions in this manual.
After a period of storage, and/or nonuse, the Weber® Built-In side burner should be checked for gas leaks and burner
obstructions before use. See instructions in this manual for correct procedures.
Do not operate the Weber® Built-In side burner if there is a gas leak present.
Do not use a fl ame to check for gas leaks.
Combustible materials should never be within 24 inches (11 mm) of the top, bottom, back or sides of your Weber®
Built-In side burner.
Do not put a barbecue cover or anything fl ammable on, or in the storage area under the barbecue. Built-In side
burner barbecue should never be used by children. Accessible parts of the barbecue may be very hot. Keep young
children away while it is in use.
You should exercise reasonable care when operating your Weber® Built-In side burner. It will be hot during cooking
or cleaning and should never be left unattended, or moved while in operation.
Should the burner go out while in operation, turn the gas valve off. Open the lid and wait fi ve minutes before
attempting to relight, using the lighting instructions.
Never lean over open side burner or place hands or fi ngers on the front edge of the side burner.
Should a grease fi re occur, turn off burner and leave lid closed until fi re is out.
Do not enlarge valve orifi ces or burner ports when cleaning the valve or burner.
The Weber® Built-In side burner should be thoroughly cleaned on a regular basis.
Liquid propane gas is not natural gas. The conversion or attempted use of natural gas in a liquid propane unit or
liquid propane gas in a natural gas unit is dangerous and will void your warranty.
Do not attempt to disconnect any gas fi tting while your barbecue is in operation.
Use heat-resistant barbecue mitts or gloves when operating barbecue.
Keep any electrical supply cord and the fuel supply hose away from any heated surfaces.
Combustion byproducts produced when using this product contain chemicals known to the state of California to
cause cancer, birth defects, or other reproductive harm.
Do not use this Built-In side burner unless all parts are in place. The unit must be properly assembled according to
the instructions outlined in the “Assembly Instruction” section of the Owners Guide.
LIQUID PROPANE GAS UNITS ONLY:
Use the regulator that is supplied with your Weber® gas barbecue.
Do not attempt to disconnect the gas regulator or any gas fi tting while your barbecue is in operation.
A dented or rusty liquid propane cylinder may be hazardous and should be checked by your liquid propane supplier.
Do not use a liquid propane cylinder with a damaged valve.
Although your liquid propane cylinder may appear to be empty, gas may still be present, and the cylinder should be
transported and stored accordingly.
If you see, smell or hear the hiss of escaping gas from the liquid propane cylinder:
1. Move away from liquid propane cylinder.
2. Do not attempt to correct the problem yourself.
3. Call your fi re department.
3
WARRANTY
WARRANTY
Weber-Stephen Products Co. (Weber) hereby warrants to the ORIGINAL
PURCHASER of this Weber® gas grill that it will be free of defects in
material and workmanship from the date of purchase as follows:
when assembled and operated in accordance with the printed instructions
accompanying it.
Weber may require reasonable proof of your date of purchase.
THEREFORE, YOU SHOULD RETAIN YOUR SALES SLIP OR
INVOICE.
This Limited Warranty shall be limited to the repair or replacement of
parts that prove defective under normal use and service and which on
examination shall indicate, to Weber’s satisfaction, they are defective.
Before returning any parts, contact the Customer service representative
in your region using the contact information sheet provided with your
manual. If Weber® confi rms the defect and approves the claim, Weber®
will elect to replace such parts without charge. If you are required to
return defective parts, transportation charges must be prepaid. Weber®
will return parts to the purchaser, freight or postage prepaid.
This Limited Warranty does not cover any failures or operating diffi culties
due to accident, abuse, misuse, alteration, misapplication, vandalism,
improper installation or improper maintenance or service, or failure to
perform normal and routine maintenance, including but not limited to
damage caused by insects within the burner tubes, as set out in this
owner’s manual.
Deterioration or damage due to severe weather conditions such as hail,
hurricanes, earthquakes or tornadoes, discoloration due to exposure
to chemicals either directly or in the atmosphere, is not covered by this
Limited Warranty.
There are no other express warrants except as set forth herein and any
applicable implied warranties of merchantability and fi tness are limited
in duration to the period of coverage of this express written Limited
Warranty. Some regions do not allow limitation on how long an implied
warranty lasts, so this limitation may not apply to you.
Weber® is not liable for any special, indirect or consequential damages.
Some regions do not allow the exclusion or limitation of incidental or
consequential damages, so this limitation or exclusion may not apply to
you.
Weber® does not authorize any person or company to assume for it
any other obligation or liability in connection with the sale, installation,
use, removal, return, or replacement of its equipment; and no such
representations are binding on Weber®.
This Warranty applies only to products sold at retail.
WEBER-STEPHEN PRODUCTS CO.
Customer Service Center
1890 Roselle Road, Suite 308
Schaumburg, IL 60195
USA
www.weber.com®
Stainless Steel Lid, 10 years
All Remaining Parts, 5 years
The natural gas supply is easy to use and gives you more cooking control than
charcoal fuel.
These instructions will give you the minimum requirements for assem-
bling your Weber® Built-In Side Burner. Please read the instructions care-
fully before using your Weber® Built-In Side Burner. Improper assembly
can be dangerous.
Not for use by children.
If there are local codes that apply to portable gas grills, you will have to
conform to them. If there are no local codes, you must conform to the lat-
est edition of the National Fuel Gas Code: ANSI Z 223.1/NFPA54.
• This Weber® Built-In Side Burner is designed for natural (piped in city)
gas only. Do not use liquid propane (LP) bottled gas. The valves, orifi ces
and hose are for natural gas only.
Do not use with charcoal fuel.
Check that the area under the control panel and the bottom tray are free
from debris that might obstruct the fl ow of combustion or ventilation air.
STORAGE
The gas must be turned OFF at the natural gas supply
when the Weber® Built-In Side Burner is not in use.
Check that the areas under the control panel and the
slide out bottom tray are free from debris that might
obstruct the fl ow of combustion or ventilation air.
OPERATING
WARNING: Only use this barbecue outdoors in a
well-ventilated area. Do not use in a garage, building,
breezeway or any other enclosed area.
WARNING: Your Weber® Built-In Side Burner shall not
be used under an unprotected combustible roof or
overhang.
WARNING: Your Weber® Built-In Side Burner is not
intended to be installed in or on recreational vehicles
and/or boats.
WARNING: Do not use the barbecue within 24 inches
of combustible materials, top, bottom, back or sides of
the grill.
WARNING: The entire cooking box gets hot when in
use. Do not leave unattended.
WARNING: Keep any electrical supply cord and the fuel
supply hose away from any heated surface.
WARNING: Keep the cooking area clear of fl ammable
vapors and liquids, such as gasoline, alcohol, etc., and
combustible materials.
GAS SUPPLY TESTING
• Disconnect your Weber® gas barbecue when the gas supply is being
tested at high pressures. This appliance and its individual shutoff valve
must be disconnected from the gas supply piping system during any
pressure testing of that system at test pressures in excess of 1/2 psig (3.5
kPa).
Turn OFF your Weber® gas barbecue when the gas supply is being tested
at low pressures. This appliance must be isolated from the gas supply
piping system by closing its individual manual shutoff valve during any
pressure testing of the gas supply piping system at the pressure equal to
or less than 1/2 psig (3.5 kPa).
4
LOCATING YOUR BUILT-IN SIDE BURNER
When determining a suitable location for your Built-In Side Burner installa-
tion, give attention to concerns such as exposure to wind, proximity to traffi c
paths, and keeping any gas supply lines as short as possible. Never locate
the Summit® Built-In Side Burner in a garage, breezeway, shed, under an
unprotected overhang, or other enclosed area. Locate the Side Burner and
structure so there is enough room to safely evacuate the area in case of a
re.
CLEARANCE FROM COMBUSTIBLE SURFACES OR
STRUCTURES
WARNING: Clearance from the outside walls of
the sides and back of the LP Tank Cabinet must be a
minimum of 24 inches any surface. Refer to “Typical Gas
Supply Installation” before starting installation.
WARNING: The structure, “island” counter tops and
adjacent work areas for the LP Tank Cabinet installation
must be built from noncombustible materials only.
NOTE: If you have questions on what materials are considered
noncombustible, contact you local building supplier or fi re department.
BUILT-IN SRUCTURE CUTOUT DIMENSIONS
All dimensions are to fi nished surfaces.
Any Surface
Any Surface
24 inches Any Surface
24 inches
24 inches
Note: For a countertop
treatment: Recommended
3/4 inch overhang. Notch
front edge for frame to
fully slide in.
Side
Burner
24 inches min.
for lid clearance
WARNING: All counter top fi nished surfaces must be
constructed of a noncombustible material.
GAS INSTRUCTIONS
Side Burner
Cut out Dimensions Tolerances
A10
12
"+
1/4
" -
1/4
"
B3
3/4
"+
1/4
" -
1/4
"
C16
1/4
"+
1/4
" -
1/4
"
5
MOUNTING THE SIDE BURNER
Connect the corrugated gas line to the side burner valve located on
the back right hand side of side burner.
TEST CONNECTIONS
All connections and joints must be thoroughly tested for leaks in
accordance with local codes and all listed procedures in the latest
edition of ANSI Z223.1/NFPA 54.
DANGER
Do not use an open fl ame to check for gas leaks. Be sure
there are no sparks or open fl ames in the area while you
check for gas leaks. This will result in a fi re or explosion
which can cause serious bodily injury or death, and
damage to property.
Be sure to secure the side burner unit with non corrosive screws
anchored into the fi nished surface of the “island structure”.
Replace the plastic plug on the front mounting hole to conceal the screw
once side burner is secure.
to regulated
gas supply
3/8" SAE stainless
corregated gas line
GAS INSTRUCTIONS
BUILT-IN GAS LINE LOCATIONS
GENERAL CONSTRUCTION DETAILS
• Summit® Built-In side burner unit should be on site before construction
begins.
All dimensions have a tolerance of plus or minus +/-
1/4
” inch.
Provide access for a corrugated gas line depending on the location of the
side burner in relation to your main gas supply and regulator position.
Area should be kept clear of sharp, jagged, or extremely abrasive surfaces
to avoid possible damage to gas supply lines. Exercise caution when pulling
gas lines through built-in structure.
A 3/8 “ inch stainless steel corrugated gas line should be used to connect
the side burner to the regulator accessory coupling.
WARNING: Do not use a rubber gas hose.
6GAS INSTRUCTIONS
Table
10-1
Maximum Capacity of Pipe in Cubic Feet of Gas per Hour for Gas Pressures of 0.5 psi or Less and a Pressure Drop of 0.3 Inch
Water Column. (Based on a 0.60 Specifi c Gravity Gas)
Nominal
Iron Pipe
Size
(Inches)
Internal
Diameter
(Inches)
Length of Pipe (Feet)
10 20 30 40 50 60 70 80 90 100 125 150 175 200
1/4 .364 32 22 18 15 14 12 11 11 10 9 8 8 7 6
3/8 .493 72 49 40 34 30 27 25 23 22 21 18 17 15 14
1/2 .622 132 92 73 63 56 50 46 43 40 38 34 31 28 26
3/4 .824 278 190 152 130 115 105 96 90 84 79 72 64 59 55
1 1.049 520 350 285 245 215 195 180 170 160 150 130 120 110 100
1 1/4 1.380 1050 730 590 500 440 400 370 350 320 305 275 250 225 210
1 1/2 1.160 1600 1100 890 760 670 610 560 530 490 460 410 380 350 320
2 2.067 3050 2100 1650 1450 1270 1150 1050 990 930 870 780 710 650 610
2 1/2 2.469 4800 3300 2700 2300 2000 1850 1700 1600 1500 1400 1250 1130 1050 980
3 3.068 8500 5900 4700 4100 3600 3250 3000 2800 2600 2500 2200 2000 1850 1700
4 4.026 17500 12000 9700 8300 7400 6800 6200 5800 5400 5100 4500 4100 3800 3500
©1997 National Fire Protection Association, Inc., and International Approval Services - U.S., Inc. All Rights Reserved.
TYPICAL NATURAL GAS SUPPLY INSTALLATION
We recommend that this installation be done by a LICENSED professional.
GENERAL SPECIFICATIONS FOR PIPING
Note - Contact your local municipality for building codes regulating outdoor
gas grill installations. In absence of Local Codes, you must conform to the
latest edition of National Fuel Gas Code ANSI Z223.1/NFPA54.
This grill is designed to operate at 4.5 inches of water column pressure.
A manual shut-off valve must be installed outdoors, and be accessible,
not in the “built-in” structure. An additional manual shut-off valve indoors
should be installed in the branch fuel line in an accessible location near
the supply line.
CAUTION: If young children are in the area, a
locking valve should be considered.
Pipe compound should be used which is resistant to the action of liquid
propane gas when gas connections are made.
The gas connections must be fi rmly attached to a rigid, permanent
construction.
Note: The information provided in this manual is general for typical
installations. We cannot cover all possible installation ideas. We recommend,
prior to installation, that you contact your municipality for local building codes
and your local fi re department for installation verifi cation.
If you have any questions, contact Customer Service at 1-800-446-1071.
GAS LINE PIPING
Refer to the piping chart at the bottom of previous page.
The corrugated gas line from the manifold is 58 inches long. Do not
extend the gas line.
We have provided the means to make an SAE 45° fl are connection. Do
not use pipe sealant on this connection.
If the length of line required does not exceed 50 feet, use a 5/8” O.D.
tube. One size larger should be used for lengths greater than 50 feet.
Refer to piping chart.
Gas piping may be copper tubing, type K or L; polyethylene plastic
tube, with a minimum wall thickness of .062 inch; or standard weight
(schedule 40) steel or wrought iron pipe.
Copper tubing must be tin-lined if the gas contains more than 0.3 grams
of hydrogen sulfi de per 100 cubic feet of gas.
Plastic tubing is suitable only for outdoor, underground use.
Gas piping in contact with earth, or any other material which may
corrode the piping, must be protected against corrosion in an approved
manner.
Underground piping must have a minimum of 18” cover.
7
Regulator
Hard piped
gas supply
top view
Figure 1
Cap
(Optional
Side Burner)
Regulator
to side burner
Hard piped
gas supply
top view
Figure 2
CONNECT GAS SUPPLY
1) Uncap the fl are fi tting from the optional side burner connection located
at regulator.
Note: You must connect your side burner to a Weber® approved regulator
(part number #62434) located at main gas supply. If you do not use a
Weber® approved regulator the Warranty on the Summit® Built-In Side
Burner will be voided. If you have any questions, contact Customer Service
at 1-800-446-1071.
2) Connect the corrugated gas line to the side burner Connection.
GAS INSTRUCTIONS
WARNING: You should check for gas leaks every time
you disconnect and reconnect a gas fi tting.
Note - All factory-made connections have been thoroughly checked for gas
leaks. As a safety precaution however, you should recheck all fi ttings for leaks
before using your Summit ® Built-In side burner. Shipping and handling may
loosen or damage a gas fi tting.
You will need: a soap and water solution, and a rag or brush to apply it.
Turn on gas supply.
Check for leaks by wetting the connections with the soap and water solution
and watching for bubbles. If bubbles form or if a bubble grows, there is a leak.
Note - Since some leak test solutions, including soap and water, may be
slightly corrosive, all connections should be rinsed with water after checking
for leaks.
WARNING: Do not ignite burners when leak checking.
TEST CONNECTIONS
All connections and joints must be thoroughly tested for leaks in accordance
with local codes and all listed procedures in the latest edition of the National
Fuel Gas Code ANSI Z223.1/NFPA 54.
DANGER
Do not use an open fl ame to check for gas
leaks. Be sure there are no sparks or open
ames in the area while you check for gas
leaks. This will result in a fi re or explosion
which can cause serious bodily injury or
death, and damage to property.
TEST CONNECTIONS
All connections and joints must be thoroughly tested for leaks in accordance
with local codes and all listed procedures in the latest edition of AS5601/
AG601.
DANGER
Do not use an open fl ame to check for gas leaks. Be sure
there are no sparks or open fl ames in the area while you
check for gas leaks. This will result in a fi re or explosion
which can cause serious bodily injury or death, and
damage to property.
8GAS INSTRUCTIONS

TOSIDE
BURNER
TOREGULATOR
TOPVIEW

Check:
1) Corrugated gas line-to-Accessory “T” Connection.
2) Main gas Supply to regulator
WARNING: If there is a leak a connection(1), retighten
the fi tting with a wrench and recheck for leaks with
soap and water solution.
If a leak persists after retightening the fi tting, turn OFF
the gas. DO NOT OPERATE THE GRILL. Contact the Cus-
tomer Service Representative in your region using the
contact information sheet provided with your manual.
Check:
When leak checks are complete, turn gas supply OFF at the source and rinse
connections with water.
SIDE BURNER LIGHTING INSTRUCTIONS
DANGER
Failure to open the lid while igniting the side
burner, or not waiting 5 minutes to allow the
gas to clear if the side burner does not light,
may result in an explosive fl ame-up which can
cause serious bodily injury or death.
LIGHTING THE SIDE BURNER
1) Open the side burner lid.
2) Check that the side burner valve is turned OFF. (Push the knob down
and turn clockwise to ensure it is in the off position.).
3) Turn the gas supply valve on.
4) Push down and turn the side burner control valve to START/HI.
5) Push igniter button and hold until burner ignites. You will hear the igniter
sparking.
CAUTION: Side burner fl ame may be diffi cult to see on
a bright sunny day.
WARNING: If the side burner does not light:
1) Turn OFF the side burner control valve.
2) Wait 5 minutes to let the gas clear before you try
again or try to light with a match.

9

(1)
(2)
(3)
OPERATING / MAINTENANCE
MANUALLY LIGHTING THE SIDE BURNER
DANGER
Failure to open the lid while igniting the side
burner, or not waiting 5 minutes to allow the
gas to clear if the side burner does not light,
may result in an explosive fl ame-up which can
cause serious bodily injury or death.
1) Open the side burner lid.
2) Check that the side burner valve is turned OFF. (Push the knob
down and turn clockwise to ensure that it is in the off position.).
3) Turn the gas supply valve on.
4) Put match in a match holder and strike match.
5) Push down and turn the side burner control valve to START/HI.
6) Hold match holder and lit match by right side of side burner.
7) Push igniter button and hold until burner ignites. You will hear the
igniter sparking.
CAUTION: Side burner fl ame may be diffi cult to see
on a bright sunny day.
WARNING: If the side burner does not light:
1) Turn OFF the side burner control valve.
2) Wait 5 minutes to let the gas clear before you
try again or try to light with a match.
TO EXTINGUISH
Push down and turn each burner control knob clockwise to the OFF
position. Turn gas supply OFF at the source.
CROSSOVER® IGNITION SYSTEM OPERATIONS
If the Crossover® ignition system fails to ignite the LEFT burner in a
burner set, light the LEFT burner with a match. If the LEFT burner lights
with a match, then check the Crossover® ignition system.
Check that both ignition wires(1,2) are attached properly.
Check that the Crossover® ignition button is activating.
You should hear the igniter sparking.
If the Crossover® ignition system still fails to light, contact the Customer
Service Representative in your area using the contact information on our
web site. Log onto www.weber.com®.
REPLACE IGNITER BATTERIES
Parts required: 1 AA alkaline battery per igniter.
Unscrew igniter button from front of control panel. Remove igniter button and
contact spring. Remove old battery and replace with a new AA
alkaline battery. Positive end (1) of battery faces inward as shown in illustra-
tion. Replace spring contact (2) and screw igniter button (3) back onto battery
compartment.
10
SIDE BURNER MAINTENANCE
WARNING: All gas controls and supply valves should
be in the OFF position.
Make sure wire is connected between the igniter and electrode. Spark should
be a white/blue color, not yellow.
1) Igniter Wire
2) Burner
(3)
Side Burner Grate
Side Burner Cap
Side Burner Ring & Head
Igniter Electrode
Control Knob
Igniter


SIDE BURNER TROUBLESHOOTING
PROBLEM CHECK CURE
Side Burner does not light. Is gas supply off? Turn supply on.
Flame is low in HIGH position Is the fuel hose bent or kinked? Straighten hose.
Push button ignition does not work. Does burner light with a match? If match lights burner, check igniter (see below).
If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your area using the contact
information on our web site. Log onto www.weber.com®.
11
ATTENTION: This product has been safety tested and is only certifi ed for use in a specifi c country. Refer to coun-
try designation located on outer carton.
These parts may be gas carrying or gas burning components. Please contact Weber-Stephen Products Co., Customer Service Department for
genuine Weber-Stephen Products Co. replacement part(s) information.
WARNING: Do not attempt to make any repair to gas carrying or gas burning components without contacting
Weber-Stephen Products Co., Customer Service Department. Your actions, if you fail to follow this product Warning,
may cause a fi re or an explosion resulting in serious personal injury or death and damage to property.
This symbol indicates that the product cannot be disposed of in the trash. For instructions regarding proper
disposal of this product in Europe, please visit www.weber.com®, and contact the importer listed for your country. If
you do not have internet access, contact your dealer for the importers name, address and telephone number.
©2003 The following trademarks are registered in the name of Weber-Stephen Products Co., an Illinois corporation, located at 200 East Daniels Road, Palatine, Illinois 60067 U.S.A.
Australia; Smokey Joe, Weber, Kettle Silhouette
®
, Genesis, Austria; Kettle Silhouette
®
, Smokey Joe, Weber, Benelux; Kettle Silhouette
®
, Smokey Joe, Weber, Compact Grill Confi gura-
tion, Botswana; Weber, Canada; Smokey Joe, Genesis, China; Kettle Silhouette
®
, Denmark; Kettle Silhouette
®
, Smokey Joe, Weber, Finland; Smokey Joe, France; Kettle Silhouette
®
,
Smokey Joe, Weber, One-Touch, Germany; Smokey Joe, Weber, One-Touch, Greece; Smokey Joe, Ireland; Kettle Silhouette
®
, Smokey Joe, Italy; Smokey Joe, Weber, Japan; Smokey
Joe, Weber, Korea; Smokey Joe, Weber, New Zealand; Weber, Smokey Joe, Nigeria; Weber, Norway; Smokey Joe, Weber, Portugal; Weber, South Africa: Smokey Joe, Weber, Kettle
Confi guration, Spain; Smokey Joe, Weber, Sweden; Kettle Silhouette
®
, Smokey Joe, Switzerland; Kettle Silhouette
®
, Smokey Joe, Weber, United Kingdom; Smokey Joe, Weber, Weber
One-Touch, U.S.A..; Kettle Confi guration, Kettle Silhouette
®
, Smokey Joe, Weber, One-Touch, Firespice, Go-Anywhere, U.S.A.;Kettle Confi guration, Kettle Silhouette, Genesis, Fla-
vorizer, Crossover, Flamgo, Performer, Rapidfi re, Tuck ‘N Carry, Jumbo Joe, Bar-B-Kettle, Master-Touch, Spirit, Grill Out, Summit, Platinum, 1-800-Grill-Out, Ranch, Matchless Flame,
Zimbabwe; Weber, Kettle Confi guration, Kettle Silhouette
®
.
WEBER-STEPHEN PRODUCTS CO.
www.weber.com®
Page 1 of 12 - Weber Weber-42377-Users-Manual- Summit BI NG SB OwnersGuideWinstall 42377 011806  Weber-42377-users-manual
Page 2 of 12 - Weber Weber-42377-Users-Manual- Summit BI NG SB OwnersGuideWinstall 42377 011806  Weber-42377-users-manual
Page 3 of 12 - Weber Weber-42377-Users-Manual- Summit BI NG SB OwnersGuideWinstall 42377 011806  Weber-42377-users-manual
Page 4 of 12 - Weber Weber-42377-Users-Manual- Summit BI NG SB OwnersGuideWinstall 42377 011806  Weber-42377-users-manual
Page 5 of 12 - Weber Weber-42377-Users-Manual- Summit BI NG SB OwnersGuideWinstall 42377 011806  Weber-42377-users-manual
Page 6 of 12 - Weber Weber-42377-Users-Manual- Summit BI NG SB OwnersGuideWinstall 42377 011806  Weber-42377-users-manual
Page 7 of 12 - Weber Weber-42377-Users-Manual- Summit BI NG SB OwnersGuideWinstall 42377 011806  Weber-42377-users-manual
Page 8 of 12 - Weber Weber-42377-Users-Manual- Summit BI NG SB OwnersGuideWinstall 42377 011806  Weber-42377-users-manual
Page 9 of 12 - Weber Weber-42377-Users-Manual- Summit BI NG SB OwnersGuideWinstall 42377 011806  Weber-42377-users-manual
Page 10 of 12 - Weber Weber-42377-Users-Manual- Summit BI NG SB OwnersGuideWinstall 42377 011806  Weber-42377-users-manual
Page 11 of 12 - Weber Weber-42377-Users-Manual- Summit BI NG SB OwnersGuideWinstall 42377 011806  Weber-42377-users-manual
Page 12 of 12 - Weber Weber-42377-Users-Manual- Summit BI NG SB OwnersGuideWinstall 42377 011806  Weber-42377-users-manual

Navigation menu