16911 1 B&G 102213Lf Submittal User Manual

User Manual: Pump 16911 1 B&G 102213Lf Submittal

Open the PDF directly: View PDF PDF.
Page Count: 2

SCHEDULE
SUBMITTAL
A-120H
JOB: REPRESENTATIVE:
UNIT TAG: ORDER NO. DATE:
ENGINEER: SUBMITTED BY: DATE:
CONTRACTOR: APPROVED BY: DATE:
Iron & Lead-Free Bronze*
Booster Pump
*Where potable water is supplied, use a lead-free bronze pump.
DESCRIPTION
Bell & Gossett in-line three-piece booster pumps are designed
for hydronic systems. Series 100 and HV are Listed with
Underwriter's Laboratories.
CONSTRUCTION
Body: Cast Iron or Lead-Free Bronze
Seal: Mechanical, Carbon on Ceramic
OPERATIONAL DATA
Maximum Working Pressure: 125 PSI (682 kPa)
Maximum Operating Temperature:
- Standard Seal: 225°F (107°C) continuous
- Special Seals: 250°F (121°C) continuous (consult local B&G Representative)
Maximum Motor RPM: 1750
Shaft: Carbon Steel, Heat Treated
Pump and Motor Bearings:
All except PD-38 and PD-40: Bronze Sleeve, Oil Lubricated
PD-38 and PD-40: Ball Bearing, Permanently Lubricated
Coupler:
All except PD38 and PD40: Flexible, Spring type
PD38 and PD40: Flexible, sleeve type.
Motor: Bell & Gossett 1/12 hp thru 1-1/2 hp standard single and three phase drip-
proof motors are Recognized under the Component Program of Underwriter's
Laboratories, Inc. Bell & Gossett boosters with their respective Bell & Gossett
manufactured standard 60 hertz single and three phase motors are Certified by
CSA.
IMPELLER:
PUMP MODEL NO. IRON BOD
Y
BRONZE BODY
Series 100® Pump Polypropylene* or Lead-Free
Brass
Polypropylene* or
Lead-Free Brass
Series HV & 2 Phenolic* or Lead-Free Brass Phenolic* or Lead-
Free Brass
PR, 2-1/2, LD3 Steel, Zinc Plated or Lead-Free
Brass
Lead-Free Brass
HD3, PD35, PD37 Steel, Zinc Plated or Lead-Free
Brass
Lead-Free Brass
PD38 & PD40 Cast Iron or Lead-Free Brass Lead-Free Brass
* System temperatures above 225 °F (107 °C) require a brass impeller.
Contains less than 0.25% Lead content by weight on wetted surfaces.
MODEL
NO.
FLANGE
SIZE NPT
INCHES
**STANDARD 60 CYCLE CHARACTERISTICS
TAGGING INFORMATION
QUANTIT
Y
HP PH
V
OLTAGE*F.L. AMPS RPM Iron Body Bronze Body
STD BI BI NFI
Series 100 3/4, 1,
1-1/4 & 1-1/2 1/12 1115 1.75 1725
Series PR 3/4, 1,
1-1/4 & 1-1/2 1/6 1115 1.9 1725
Series HV 1, 1-1/4
& 1-1/2 1/6 1115 1.9 1725
2 2 1/6 1115 1.9 1725
2-1/2 2-1/2 1/4 1115 3.0 1725
LD3 31/4 1115 3.0 1725
HD3 31/3 1115/230 4.2/2.1 1725
PD-35S 31/2 1115/230 5.2/2.6 1725
PD-35T 31/2 3208-230/460 1.8-1.7/.85 1750
PD-37S 33/4 1115/230 7.0/3.5 1725
PD-37T 33/4 3208-230/460 2.45-2.4/1.2 1750
PD-38S 3 1 1 115/230 9.8/4.5 1725
PD-38T 3 13208-230/460 3.4-3.4/1.7 1725
PD-40S 31-1/2 1115/230 18.0/9.0 1725
PD-40T 31-1/2 3208-230/460 4.8-4.8/2.4 1725
**Motors with special electrical characteristics are available on request at additional cost.
*1 PH Motors: Built-in overload protection
3 PH Motors: Overload protection must be provided
Bell & Gossett Booster Pumps equipped with a drip-proof motor are recommended for indoor use only.
Iron & Bronze Booster Pump Submittal A-120H
MODEL
NO.
FLANGE
SIZE NPT
INCHES
DIMENSIONS IN INCHES
(
MM
)
A
PPROX. SHPG.
WT. LBS.
(
K
g)
ABCIRON
BODY BRONZE
BOD
Y
Series 100 3/4, 1,
1-1/4 & 1-1/2
14-7/8
(378)
6-3/8
(162)
12-3/4
(324)
20
(9)
21
(10)
Series PR 3/4, 1,
1-1/4 & 1-1/2
15-1/4
(387)
8-1/2
(216)
12-3/4
(324)
30
(14)
32
(15)
Series HV 1,
1-1/4 & 1-1/2
15-3/8
(391)
8-1/2
(216)
13
(330)
28
(13)
30
(14)
2 216-5/8
(422)
8-1/2
(216)
14
(356)
36
(16)
39
(18)
2-1/2 2-1/2 17-1/4
(
438
)
10
(
254
)
14
(
356
)
54
(
24
)
58
(
26
)
LD3 317-1/4
(
438
)
10
(
254
)
14
(
356
)
53
(
24
)
57
(
26
)
HD3 317-1/2
(
444
)
10
(
254
)
14-1/4
(
362
)
55
(
25
)
59
(
27
)
PD-35S 320-1/4
(
514
)
12
(
305
)
16-7/8
(
429
)
75
(
34
)
80
(
36
)
PD-35T 320-1/4
(514)
12
(305)
16-7/8
(429)
75
(34)
80
(36)
PD-37S 320-1/4
(514)
12
(305)
16-7/8
(429)
75
(34)
80
(36)
PD-37T 320-1/4
(514)
12
(305)
16-7/8
(429)
75
(34)
80
(36)
PD-38S 322-11/16
(576)
14-1/2
(368)
18-15/16
(481)
128
(58)
138
(63)
PD-38T 323-15/16
(608)
14-1/2
(368)
20-3/16
(513)
125
(57)
135
(61)
PD-40S 324-3/4
(629)
14-1/2
(368)
21
(533)
130
(59)
140
(64)
PD-40T 321-7/8
(556)
14-1/2
(368)
18-1/8
(460)
127
(58)
137
(62)
Dimensions are subject to change.
Not to be used for construction purposes unless certified.
TYPICAL SPECIFICATIONS
Electrical Box Arran
ement for pumps with B&G Manufactured Motors
MODEL
NO. #1 #2 #3 #4
Series 100 115 & 230Volt 60Hz 1PH
110 & 220Volt 50Hz 1PH − −
Series HV, PR & 2 115 & 230Volt 60Hz 1PH
110 & 220Volt 50Hz 1PH 3PH
2-1/2", LD3 & HD3 1PH − −
PD35 & PD37 ALL
PD38 & PD40 ALL
The Contractor shall furnish and install In-The-Line pumps as illustrated on the
plans and in accordance with the following specifications:
1. The pumps shall be of the horizontal, oil-lubricated type. (Except PD-38, PD-
40 are permanently lubricated) Specifically designed and guaranteed for quiet
operation. Suitable for 125# (862 kPa) working pressure.
2.The pumps shall have a ground and polished steel shaft with a hardened
integral thrust collar. The shaft shall be supported by two horizontal sleeve
bearings designed to circulate oil. (Except PD-38, PD-40 are grease lubricated
ball bearing design) The pumps are to be equipped with a mechanical seal with
carbon seal face rotating against a ceramic seat. The motor shall be non-
overloading at any point on pump curve.
3. The motor shall be of the drip-proof, sleeve-bearing, (Except PD-38, PD-40
are ball bearing) quiet operating, rubber-mounted construction. Motors shall
have built-in thermal overload protectors. (Exception - PD models with 3-phase
motors, see paragraph 4.)
4. For PD models with 3-phase motors, add the following: The Contractor shall
furnish and install a magnetic starter for each booster pump with at least two
thermal overload protectors. The starter shall be equipped with manual reset
buttons.
A
ll Units must be ITT Bell & Gossett Model No. ________, or approved equal
with capacity of ______GPM at ______ft. head when directly driven through a
self aligning flexible coupling by an oil lubricated motor, _____volts
_
___c
y
cle___phase.
Xylem Inc.
8200 N. Austin Avenue
Morton Grove, IL 60053
Phone: (847)966-3700
Fax: (847)965-8379
www.xyleminc.com/brands/bellgossett
Bell & Gossett is a trademark of Xylem Inc. or one of its subsidiaries.
© 2012 Xylem Inc.

Navigation menu