16884 1 B&G 1Bl003Lf Submittal User Manual

User Manual: Pump 16884 1 B&G 1Bl003Lf Submittal

Open the PDF directly: View PDF PDF.
Page Count: 2

Download16884 1 B&G 1Bl003Lf Submittal  User Manual
Open PDF In BrowserView PDF
SUBMITTAL
A-135E
JOB:

REPRESENTATIVE:

UNIT TAG:

ORDER NO.

ENGINEER:

SUBMITTED BY:

CONTRACTOR:

APPROVED BY:

DATE:
DATE:
DATE:

Permanently Lubricated
Iron & Lead-Free† Bronze Booster
Pumps
DESCRIPTION
The Series PL™ close coupled booster pumps are
specifically designed for quiet operation in hydronic,
radiant and geothermal heating and cooling systems.
These inline permanently lubricated pumps are available
in cast iron or lead-free† bronze body construction.
OPERATING DATA
Maximum working Pressure: 150 psi (10 Bar)
Maximum Operating Temperature: 225°F (107°C)
† Contains less than 0.25% Lead content by weight on wetted

surfaces.

CONSTRUCTION MATERIALS
Booster Body: Cast Iron or Lead-Free† Bronze
Face Plate: Stainless Steel
Impeller: 30% Glass Filled Noryl®
(PL-55 & PL-130): Glass Filled PPS
Shaft: Carbon Steel
(PL-55 & PL-130): Stainless Steel
Shaft Sleeve: Stainless Steel
(PL-55 & PL-130): None
Seal: Mechanical, Carbon on Silicon Carbide
Motor Bearings: Sealed Precision Steel Ball Bearing
Permanently Lubricated
Motor Type: ODP
Elastomers: EPDM

SCHEDULE
MODEL
NUMBER
PL-30
PL-30
PL-36
PL-36
PL-45
PL-45
PL-50
PL-50
PL-55
PL-55
PL-75
PL-75
PL-130/2"
PL-130/2"
PL-130/3"
PL-130/3"

CAST IRON
PART
NUMBER
1BL012
1BL014
1BL001
1BL006
1BL002
1BL007
1BL016
1BL018
1BL032
1BL033
1BL034
1BL036
1BL063
1BL064
1BL070
1BL071

QTY.

LEAD-FREE† BRONZE
MODEL
PART
NUMBER
NUMBER
QTY.
PL-30B
1BL013LF
PL-30B
1BL015LF
PL-36B
1BL003LF
PL-36B
1BL008LF
PL-45B
1BL004LF
PL-45B
1BL009LF
PL-50B
1BL017LF
PL-50B
1BL019LF
PL-55B
1BL068LF
PL-55B
1BL069LF
PL-75B
1BL035LF
PL-75B
1BL037LF
PL-130B/2" 1BL065LF
PL-130B/2" 1BL066LF
PL-130B/3" 1BL072LF
PL-130B/3" 1BL073LF

STANDARD 60 CYCLE SINGLE PHASE
MOTOR CHARACTERISTICS
HP
VOLTAGE F.L. AMPS RPM
1/12
115
1.4
2650
1/12
230
0.8
2650
1/6
115
2.1
3300
1/6
230
1.1
3300
1/6
115
2.1
3300
1/6
230
1.1
3300
1/6
115
1.8
3300
1/6
230
1.0
3300
2/5
115
4.7
3250
2/5
230
2.4
3250
1/6
115
2.1
3400
1/6
230
1.1
3400
2/5
115
4.8
3200
2/5
230
2.4
3200
2/5
115
4.8
3200
2/5
230
2.4
3200

Note: Where potable water is pumped, use a lead-free† bronze booster.
PL boosters equipped with a drip-proof motor are recommended for indoor use only.

TAGGING INFORMATION

SERIES PL - Permanently Lubricated Booster Pumps

A-135E

DIMENSIONS AND WEIGHTS
MODEL NO.
PL-30
PL-36
PL-45
PL-50
PL-55
PL-75
PL-130/2"
PL-130/3"

FLANGE SIZE
INCHES - NPT
3/4, 1,
1-1/4 & 1-1/2
3/4, 1,
1-1/4 & 1-1/2
1, 1-1/4
& 1-1/2
1, 1-1/4
& 1-1/2
3/4, 1,
1-1/4 & 1-1/2
2
2
3

MOTOR HP

A

B

C

D

E

APPROXIMATE
SHIPPING WT.
LBS. (KG)

1/12

8 5/8 (219)

6 3/8 (162)

7 1/8 (181)

4 3/16 (106)

4 3/8 (111)

11.6 (5.3)

1/6

8 5/8 (219)

6 3/8 (162)

7 1/8 (181)

4 3/16 (106)

4 3/8 (111)

13.1 (6.0)

1/6

9 1/8 (232)

8 1/2 (216)

7 1/4 (184)

4 5/8 (117)

4 1/2 (114)

14.5 (6.6)

1/6

9 1/8 (232)

8 1/2 (216)

7 1/4 (184)

4 5/8 (117)

4 1/2 (114)

14.5 (6.6)

2/5

9 9/16 (243)

6 3/8 (162)

7 15/16 (202)

4 3/16 (106)

4 3/4 (121)

13.1 (6.0)

1/6
2/5
2/5

9 15/16 (252)
10 3/4 (273)
10 3/4 (273)

8 1/2 (216)
8 1/2 (216)
8 1/2 (216)

7 3/8 (187)
8 1/4 (210)
8 1/4 (210)

5 3/16 (132)
5 3/16 (132)
6 (152)

4 5/8 (117)
5 1/8 (130)
5 1/8 (130)

18.5 (8.4)
22 (10)
27 (12.2)

DIMENSIONS - INCHES (mm)

Dimensions are approximate and subject to change. Contact factory for certified dimensions.
PERFORMANCE CHARACTERISTICS CURVES

TYPICAL SPECIFICATIONS
The contractor shall furnish and install inline pumps
as illustrated on the plans and in accordance with
the following specifications:
1. The pumps shall be of the horizontal, permanently
lubricated
type,
specifically
designed
and
guaranteed for quiet
operation.
2. The pumps shall have a steel shaft supported by
permanently lubricated, sealed precision ball
bearings. The pumps are to be equipped with a
water-tight seal to prevent leakage. Mechanical seal
faces to be carbon on silicon carbide. The motor
shall be non-overloading at any point on the pump
performance curve.
3. The motor shall be of the drip-proof, sealed
precision ball-bearing, quiet-operating construction.
The permanent split-capacitor motor shall be
equipped with thermal overload protection.
4. Pumps to be suitable for 225°F (107°C) operating
temperature at 150 psig (10 bar) working pressure.
The pumps shall be ITT Bell & Gossett Model No.
PL-__________ with a capacity of __________
GPM at __________ feet of head.

Xylem Inc.
8200 N. Austin Avenue
Morton Grove, IL 60053
Phone: (847)966-3700
Fax: (847)965-8379
www.xyleminc.com/brands/bellgossett
Bell & Gossett is a trademark of Xylem Inc. or one of its subsidiaries.
© 2012 Xylem Inc.



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : Mtripp
Create Date                     : 2012:11:13 10:44:11-06:00
Modify Date                     : 2013:03:19 15:45:40-04:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2013:03:19 15:45:40-04:00
Producer                        : Acrobat Distiller 10.0.0 (Windows)
Format                          : application/pdf
Title                           : http://rep.xyleminc.com/htmlsubmittals/booster/A-135D--page1.st
Creator                         : Mtripp
Document ID                     : uuid:5c44a148-ed98-410c-88b9-3fd11f2a2f20
Instance ID                     : uuid:52b8768c-03a6-4691-bcf5-08bce49760f9
Page Count                      : 2
EXIF Metadata provided by EXIF.tools

Navigation menu