Miele Cva 4075 En Ca Users Manual S

CVA 4075 EN-CA to the manual 521b42fb-6c0f-4a58-8269-21e3b8357673


: Miele Miele-Cva-4075-En-Ca-Users-Manual-221973 miele-cva-4075-en-ca-users-manual-221973 miele pdf

Open the PDF directly: View PDF PDF.
Page Count: 7

DownloadMiele Miele-Cva-4075-En-Ca-Users-Manual- S  Miele-cva-4075-en-ca-users-manual
Open PDF In BrowserView PDF
Installation Instructions
CVA 4075 en-CA
Installation, repair and maintenance work should be performed by
a Miele authorized service technician in accordance with national
and local safety regulations and the provided installation instructions.

The machine must be connected to
the water supply in accordance with
local and national regulations.
The water being used should have
the drinking water standards of the
respective country where the
machine is used.
– All units and systems used to deliver
the water to the coffee system must
conform with the requirements of the
respective country.
– The machine is designed to be
plumbed to a cold water connection.

Connection to the water
^ Disconnect the machine from the
electrical supply.
^ Remove the water connection cover
at the lower rear side of the coffee
^ Screw the supplied brass
compression fitting, with the ¾" end,
tightly onto the water connector of the
coffee machine. The fitting includes
an opening for standard ¼" piping.

– The machine can be connected
without a non-return valve.
– The on-site water line must have a
water valve to turn the water off if
needed. If not present, have a water
valve installed by a licensed
– The water faucet must be accessible
after installation.

^ Connect the compression fitting to
the water supply.
^ Check for leaks.

– Water pressure on-site:
Minimum: 14.5 psi
Maximum: 145 psi, if higher, install a
pressure reduction valve.
– Suitable 1/4" tubing or copper piping
must be supplied for plumbing.
– To ensure the best coffee quality, the
maximum length of the tubing or
copper pipe should not exceed
4 ft. 11" (1.5 m). If too much water
remains in the tubing the coffee
quality could be affected.


Electrical connection
Ensure that power is not supplied to
the machine while installation or
maintenance work is performed.
All electrical work should be
performed by a qualified electrician
in strict accordance with national
and local safety regulations.
Installation, repairs and other work
by unqualified persons could be
The manufacturer cannot be held
responsible for unauthorized work.
Verify that the voltage, load and circuit
rating information found on the data
plate match the household electrical
supply before installing the coffee
If there is any question concerning the
electrical connection of this appliance
to your power supply, please consult a
licensed electrician or contact Miele’s
Technical Service Department. See
back page for contact information.


The coffee system comes equipped
with a 6 ft (1.8 m) power cord with a
NEMA 5-15P molded plug for
connection to a 120 V, 15 A, 60 Hz
power supply.

Installation options
The coffee system is designed to be
built into cabinetry.

A combination with other Miele built in
appliances is possible. If the machine
is installed in combination with other
appliances, it should be installed with a
protective base between the appliance
and the unit (exception: installation with
a built-in plate warmer).
A special display cabinet is also
available from your dealer or Miele, as
an installation option.


Make sure power is not supplied to
the appliance while installation or
maintenance work is performed.
Disconnect the power supply to the
work area by unplugging the unit,
tripping the circuit breaker or
removing the fuse. The coffee
system must be installed into
cabinetry before being used.

^ If your cabinet has 3/4" (19 mm) side
walls, drill four holes for the
^ Center the unit and turn the screws a
little bit in and then out again.
^ Take the unit out of the niche and drill
four holes at the screw markings
(1/16" [2 mm], diameter 3/16"
[4.5 mm]).
^ Connect the appliance to a cold
water supply.
^ Plug the appliance into the electrical
^ Push the appliance into the niche.
^ Open the door and partially tighten
the screws.

^ Unscrew the height adjustable feet
on the underside of the machine
about 1/16" (2 mm).
^ Push the appliance all the way back
into the cabinet and center it. If
necessary level the unit with the four
height adjustable feet.
The feet can be turned out up to 3/8"
(10 mm).

^ Carefully turn the lower screws, a, to
center the machine.
^ To secure the appliance in the
cabinet, tighten the upper screws, b,
by hand. Do not use an electric


Adjusting the door hinges
The door hinges can be adjusted if the
door cannot be opened easily.

^ To adjust the door sideways, a, turn
screw a.
^ To adjust the door to the front or
back, b, turn screw b.


Alteration rights reserved / 2707
with convertible water connection
CVA 4075

For the most updated manual see the Miele website.

M.-Nr. 06 984 320 / 03


Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Page Mode                       : UseOutlines
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2007:11:07 10:13:30-05:00
Create Date                     : 2007:06:29 10:06:22-04:00
Metadata Date                   : 2007:11:07 10:13:30-05:00
Format                          : application/pdf
Title                           : S:\Tech Writing\Data\CVA\us\vp\CVA4075_us.vp
Creator                         : USASEIL
Document ID                     : uuid:3178fcf1-2202-4d2d-91fb-cd2cfc6d53dd
Instance ID                     : uuid:79c80943-4630-4bdf-bedb-c44588f29513
Has XFA                         : No
Page Count                      : 7
Author                          : USASEIL
EXIF Metadata provided by EXIF.tools

Navigation menu